How to Replace a Bath Tub
How to Replace a Bath Tub
Blog Article
In this article below you can get a good deal of wonderful information regarding Installing A Bathtub.
Installing a bathtub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and also often, tiling skills. Replacing an old tub with a new one is additionally a moderately difficult task. If the old tub is readily easily accessible, the project can relocate immediately; if you have to open up a wall to remove the old bathtub and place the brand-new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to vacate the old bathtub and embeded in the brand-new one. Ensure you have actually qualified on your own for the task and also are comfortable trying it. Instead of hiring a specialist to take over a halfway-completed task, it is far better to think about utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This short article will assist you mount a brand-new bathtub in your shower room if you have already acquired a new bathtub and do not require to alter the setup of your previous supply of water pipelines.
Your tools as well as product checklist must comprise the following:
Getting ready for the Installment
Firstly, the supporting structure supplied with the bath must be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you make use of all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its final placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will originate from the pipelines. When the supply pipes have been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming during this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Prior to carrying on to fit the brand-new faucets, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Bath tub
Making use of the two wooden boards under its feet, position the bath tub in the called for setting. The wooden boards are helpful in evenly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto 4 tiny points.
The next goal is to make certain that the tub is leveled all round. This can be achieved by checking the level as well as changing the feet on the bathtub till the level checks out level.
To install faucets, fit all-time low of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Switch on the water system and check all joints and also brand-new pipework for leaks and tighten them if necessary. Load the tub and also examine the overflow electrical outlet as well as the normal outlet for leakages.
Lastly, repair the bath paneling as defined in the maker's instruction manual. Tiling and securing around the tub should wait till the tub has been made use of at the very least once as this will certainly resolve it into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making sure that the washing machines are in area between the faucet and also the sink. Protect the faucet in place with the maker given backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type must be attached to the tap ends initially, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a rigid seal, triggering the water to permeate the wall surface between the bath as well as the tiling, causing issues with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill the bathtub with water before sealing, to enable the motion experienced when the tub remains in usage. The sealer can split rather very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader on Tools You Need to Install a New Bathtub , I was thinking sharing that short article was smart. You should take the time to share this content if you liked it. We love reading our article about How to Install a Bathtub.
Visit My Web Page Report this page